Festool CS 70 E PRECISIO Bedienungsanleitung PDF herunterladen (Seite 19)

PRECISIO -

This beds in the splinterguard. The raised sec-

tion [8-4] of the splinterguard should protrude

slightly (approx. 0.3 mm) over the edge of the

table so that the splinterguard functions more

effectively.

Unscrew both screws [8-2] to adjust the height

of the retainer [8-1].

7.9 Dust extraction

CAUTION

Breathing in dust can damage the respiratory

passage!

Always connect the machine to a dust extrac-

tor.

When performing work that generates dust,

always wear a dust mask.

The PRECISIO has two extraction connectors: top

protective cover [3-7] 27 mm in diameter and the

lower protective cover [3-3] 35 mm in diameter.

Attach the hose holder [3-6] to the clamp rail on

the saw base to guide the top suction hose.

The extractor set CS 70 AB [3-4] (included in

CS 70 EB scope of delivery) joins both extraction

connectors so that a Festool mobile dust extrac-

tor with 50 mm adapter can be connected.

8 Working with the machine

WARNING

Risk of injury

Always read all safety instructions when

working with the machine!

Never work with the machine in the front po-

sition (set-up position).

Make sure that all rotary knobs on the fence

and the machine are tightened before start-

ing work.

Adjust the top protective cover until it rests on

the workpiece and secure in this position using

the rotary knob [1-11].

8.1 Using the machine as a bench-mounted

circular saw

When used in bench-mounted applications, the

saw is ﬁ xed and the workpiece is moved.

Pull the saw forwards.

Allow the saw to glide back slowly.

You can push the stop lever [1-7] down after a

few millimetres.

If the saw continues to glide back, the stop lever

engages in the guide rod and secures the saw at

the centre of the table (bench saw position).

Use the fence as a longitudinal stop [Fig. 6] to

guide the workpiece.



Guide the workpiece by hand. Use the work-

piece holder [6-1] to guide the workpiece ac-

curately past the saw blade.

Place the workpiece holder in the store [2-7]

when not in use.

8.2 Using the machine as a trimming saw

When the machine is used for trimming work,

the workpiece remains stationary and the saw is

moved to make the cut.

Turn the rotary knob [2-6] anticlockwise to re-

lease the saw lock.

Push down the stop lever [1-7] to unlock and

move the saw to the forward position so that the

control elements are easy accessible when the

saw settings are adjusted. Turn the rotary knob

[2-6] anticlockwise to release the lock again.

Attach the cross or angle stop [Fig. 1] so that

the workpiece is retained securely on the saw

base.

Alternatively, insert clamps (accessories) in

the groove [1-10] to secure the workpiece.

Use the rotary knob [2-6] to draw the saw for-

wards and make the cut.

After completing the cut, move the saw unit

right back to its starting position before re-

moving the workpiece from the fence.

9 Service and maintenance

WARNING

Risk of accident, electric shock



Always pull the plug from the mains power

supply before maintaining, servicing or mak-

ing any kind of adjustment.

All maintenance and repair work which re-

quires the motor housing to be opened, must

only be carried out by an authorised service

workshop.

Damaged safety devices and parts should be

repaired or replaced by an authorised service

centre unless otherwise speciﬁ ed in the op-

erating instructions.

The machine is equipped with special self-dis-

connecting carbon brushes. If they are worn, the

power is interrupted automatically and the ma-

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 115 116

Kommentare zu diesen Handbüchern

Keine Kommentare

Festool CS 70 E PRECISIO Bedienungsanleitung Seite 19

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Elektrowerkzeuge Festool CS 70 E PRECISIO